logo
Yuhong Holding Group Co.,LTD
Products
About Us
Factory Tour
Quality Control
Contact Us
Home News

How Is Stainless Steel Hardness Tested After Heat Treatment? Brinell, Rockwell and Vickers Compared

Certifications
China Yuhong Group Co.,Ltd certification
Customers Reviews
Yuhong Group work as team with us start from 2003, and support excellent service for us last 9 years of steel pipe/tube

—— Singapore---Mr. How

Stable quality , good price, excellent serive, Yuhong Special Steel already become our partner in business team.

—— Colombia ---LEO

Good quality , we like that ! And delivery time in time also , that is why we place repeat order for Yuhong Special Steel .

—— Dubai ---Nazaad

boiler tube / heat exchanger tube expert . We like your quality .

—— USA- JAMES

I'm Online Chat Now
Company News
How Is Stainless Steel Hardness Tested After Heat Treatment? Brinell, Rockwell and Vickers Compared
Latest company news about How Is Stainless Steel Hardness Tested After Heat Treatment? Brinell, Rockwell and Vickers Compared
How Is Stainless Steel Hardness Tested After Heat Treatment? Brinell, Rockwell and Vickers Compared

By the Yuhong Group technical team · 16 November 2026

Hardness is the most frequently specified property after heat treatment, and the one most often reported without the information needed to interpret it. A number without the test method, indenter type and load is not a specification — Brinell, Rockwell and Vickers measure different things and their values are not interchangeable. This article covers the three methods, which grades and heat-treatment states each suits, and what a test report should state.

Brinell Hardness (HBW / HBS)

A hard-alloy ball of defined diameter is pressed into the surface under a specified load, held for a defined time, and the indentation diameter is measured after unloading. The hardness value is calculated from the load, ball diameter and indentation diameter.

With a tungsten-carbide ball the designation is HBW; with a steel ball it is HBS. The ball diameter is typically 10, 5, 2.5 or 1 mm, and the load-to-ball ratio (F/D²) can be 30, 10, 5, 2.5 or 1, giving loads from 9.807 N to 29,420 N. The hold time is usually 10–15 s.

The result is written with the test conditions: 285 HBW 10/3000 means a 10 mm carbide ball and a 29,420 N (3000 kgf) load. A value without these conditions cannot be compared with another Brinell result.

Brinell suits austenitic and duplex stainless after solution annealing, martensitic grades after quenching and tempering, and precipitation-hardening grades after ageing. It is less suitable for very hard or thin sections, where the indentation is large relative to the section.

Rockwell Hardness (HRA / HRB / HRC)

A diamond cone or a steel ball is first loaded with a minor load (F₀), then a major load (F₁). After the major load is removed, the residual penetration depth is measured, and the hardness is calculated from that depth and the scale constants. The indenter, loads and constants all depend on the scale.

The common scales for stainless steel are HRA (diamond cone, for very hard thin material), HRB (1.588 mm steel ball, for soft annealed grades) and HRC (diamond cone, for hardened martensitic grades). The designation carries the scale: 60 HRC is 60 on the C scale, 60 HRB is 60 on the B scale — the two are not comparable.

Rockwell is faster and leaves a smaller indentation, which suits finished parts and production control. Its limitation is that the scale must match the hardness range; the wrong scale gives a meaningless reading.

Vickers Hardness (HV)

A square-based diamond pyramid is pressed into the surface under a specified load, and both indentation diagonals are measured. The hardness is the load divided by the indentation surface area, calculated from the mean diagonal.

The load is written with the result: 700 HV5 means 700 HV at 49.03 N (5 kgf). Vickers is the method for hardened surfaces, case-hardened layers and thin sections where a small indentation is required, and the method most often used for surface-hardening depth measurements.

What a Hardness Report Must State

A hardness value alone does not define the delivered condition. The report should state:

  • The test method — Brinell, Rockwell or Vickers.
  • The indenter or ball type and diameter — carbide or steel, 10 mm or 5 mm, diamond cone or pyramid.
  • The test load and, for Brinell, the hold time.
  • The scale, for Rockwell — HRA, HRB or HRC.
  • The sample location and the heat number, so the result traces to the delivered product.

The test itself also has requirements: a smooth, clean surface (typically ≤1.6 µm roughness for Brinell, ≤0.8 µm for Rockwell), a specimen thickness of at least 8× the indentation depth for Brinell and 10–15× the residual depth for Rockwell, and indentation spacing and edge distance meeting the standard.

Frequently Asked Questions

What is the difference between Brinell, Rockwell and Vickers hardness testing?
Brinell presses a ball and measures the indentation diameter; Rockwell measures the residual penetration depth after a major load; Vickers presses a diamond pyramid and measures the diagonal length. Each suits a different hardness range and section thickness, and the results are not interchangeable.

What does HBW and HBS mean?
HBW is Brinell hardness measured with a tungsten-carbide ball; HBS with a steel ball. The designation is followed by ball diameter, load and hold time, for example 285 HBW 10/3000.

Which hardness method is used for austenitic stainless steel after solution annealing?
Brinell is commonly used for austenitic and duplex stainless after solution annealing, and for martensitic grades after hardening and tempering. Rockwell and Vickers are used where a smaller indentation is needed.

Why can't I compare an HRC value with an HRB value?
The two scales use different indenters and loads, and the numbers are defined differently, so an HRC value and an HRB value for the same material cannot be compared directly.

Hardness testing machine used for stainless steel tube after heat treatment

Pub Time : 2026-11-17 09:41:31 >> News list
Contact Details
Yuhong Group Co.,Ltd

Contact Person: Mr. Jikin Cai

Tel: +86-13819835483

Fax: 0086-574-88017980

Send your inquiry directly to us (0 / 3000)