Yuhong Holding Group Co.,LTD
The room-temperature tensile test produces the numbers used in design calculations. It measures four properties: yield strength, tensile strength, elongation after fracture and reduction of area. Each answers a different question, and reading a mill test certificate without understanding the difference leads to the wrong grade being accepted — or the right grade being rejected.
The Test: Elastic, Plastic and FractureWhen a tensile specimen is loaded, it first deforms elastically: the extension is proportional to the load, and the specimen returns to its original length when the load is removed. Beyond the yield point, part of the deformation becomes plastic and remains.
For most austenitic stainless steels, there is no distinct yield point — the transition from elastic to plastic is gradual. That is why yield strength is reported as a proof strength, usually Rp0.2: the stress at which 0.2% plastic extension has occurred.
After yielding, the specimen deforms under increasing load until it reaches a maximum, then necks locally and fractures.
Yield Strength: The Design BasisYield strength is the stress at which the material begins to deform plastically. For ductile materials it is the design basis, because a component is normally designed to stay below yield in service.
For stainless steel, yield strength has two additional implications. A higher yield strength means greater sensitivity to stress-corrosion cracking and hydrogen embrittlement, and reduces cold formability and weldability. That is why a higher-yield grade is not automatically better — the specification has to match the forming and welding route.
Yield strength is affected by composition, microstructure, temperature, loading rate and heat treatment. Solution annealing lowers the yield strength of austenitic grades and restores ductility; cold working raises it. Both are legitimate, but the resulting properties differ.
Tensile Strength: Maximum Uniform DeformationTensile strength (Rm) is the maximum stress before necking begins — the peak load divided by the original cross-sectional area. It represents resistance to uniform deformation and is one of the primary design and selection parameters.
Tensile strength is easier to measure — the peak load divided by the original area — and is less sensitive to test method.
Elongation and Reduction of Area: DuctilityElongation after fracture (A) is the permanent extension of the gauge length, expressed as a percentage of the original gauge length.
Elongation depends on the gauge length. A gauge length of 5 × diameter gives A5; 10 × diameter gives A10. For the same material, A5 is normally higher than A10, because the shorter gauge length includes a larger fraction of the necked region. A5 and A10 are not directly comparable — a specification that says “elongation ≥ 40%” without stating A5 or A10 is incomplete.
Reduction of area (Z) is the maximum reduction in cross-sectional area at the fracture, as a percentage of the original area. Together with elongation, it describes ductility.
What to Check on the Mill Test CertificateWhy is yield strength reported as Rp0.2 for stainless steel?Most austenitic stainless steels do not show a distinct yield point, so the yield strength is reported as the 0.2% proof strength — the stress at which 0.2% plastic extension has occurred.
Why are A5 and A10 elongation values not comparable?Elongation depends on the gauge length. A5 uses a gauge length of 5 × diameter and A10 uses 10 × diameter; the shorter gauge includes a larger fraction of the necked region, so A5 is normally higher. A specification must state which one it refers to.
Does a higher yield strength mean a better stainless steel?Not necessarily. Higher yield strength increases sensitivity to stress-corrosion cracking and hydrogen embrittlement, and reduces cold formability and weldability. The grade has to match the forming and welding route, not just the design stress.
What is the difference between tensile strength and yield strength?Yield strength is the stress at which plastic deformation begins; tensile strength is the maximum stress before necking. Yield strength is the design basis for ductile materials, while tensile strength describes resistance to uniform deformation.
Yuhong Group mill test certificates report yield (Rp0.2), tensile strength, elongation (A5 or A10) and reduction of area, traceable to the heat number.
![]()
![]()
Contact Person: Mr. Jikin Cai
Tel: +86-13819835483
Fax: 0086-574-88017980